C1045 High Tensile UNC Threaded Tie Rods

High Tensile NC Threaded Bar
Bar
Diameter
& Pitch
Minimum
Net Area
Thru Threads
Minimum
Ultimate
Strength
Minimum
Yield
Strength
Part
Number
3/8” – 16
(9.5 mm)
0.08 in2
(50 mm2)
9.3 kips
(41 kN)
7.1 kips
(32 kN)
B8S-03
1/2” – 13
(13 mm)
0.14 in2
(92 mm2)
17 kips
(76 kN)
13 kips
(58 kN)
B8S-04
5/8” – 11
(16 mm)
0.23 in2
(146 mm2)
27 kips
(121 kN)
21 kips
(93 kN)
B8S-05
3/4” – 10
(19 mm)
0.33 in2
(216 mm2
40 kips
(178 kN)
31 kips
(137 kN)
B8S-06
7/8” – 9
(22 mm)
0.46 in2
(298 mm2)
55 kips
(247 kN)
43 kips
(189 kN)
B8S-07
1” – 8
(25 mm)
0.61 in2
(391 mm2)
73 kips
(324 kN)
56 kips
(248 kN)
B8S-08
1-1/8” – 7
(28 mm)
0.76 in2
(492 mm2)
80 kips
(356 kN)
62 kips
(275 kN)
B8S-09
1-1/4” – 7
(32 mm)
0.97 in2
(625 mm2)
102 kips
(453 kN)
79 kips
(349 kN)
B8S-10
1-3/8”
(35 mm)
1.23 in2
(794 mm2)
129 kips
(575 kN)
100 kips
(443 kN)
B8S-11
1-1/2” – 6
(38 mm)
1.41 in2
(906 mm2)
148 kips
(656 kN)
114 kips
(506 kN)
B8S-12
1-3/4”
(45 mm)
1.90 in2
(1226 mm2)
200 kips
(887 kN)
154 kips
(685 kN)
B8S-14
2” – 6
(51 mm)
2.65 in2
(1710 mm2)
278 kips
(1238 kN)
215 kips
(955 kN)
B8S-16

Structural Properties

Yield
Stress
Ultimate
Stress
Elongation in
2″ bar diameter
Reduction
of Area
90 / 81 KSI KSI
(621 / 558 MPa)
120 / 105  KSI
(827 / 723 MPa)
11% 20%

Williams High Tensile UNC Tie Rods are available in all diameters shown, with lengths from 3” to 20’-0”.  They are available all-threaded, thread one end, or threaded both ends. Short length tie rods threaded both ends under 2’-0” are usually crimped to prevent rotation in the concrete during removal of the Shebolt.  Ties threaded each end allow easy spot-checking of the connection, to insure proper engagement.


Accessories

C2T Stop-Type & Flange Couplings

High Tensile NC Threaded Bar

Bar
Diameter
Outside
Diameter
Overall
Length
Stop-Type
Part Number
Flange Coupling
Flange Size Part Number
1/4”
(6.4 mm)
1/2”
(13 mm)
7/8”
(22 mm)
C2T-02
3/8”
(9.5 mm)
3/4”
(19 mm)
1-1/2”
(38 mm)
C2T-03 2” x 2”
(51 x 51 mm)
C2D-03
1/2”
(13 mm)
3/4”
(19 mm)
1-1/2”
(38 mm)
C2T-04 2” x 2”
(51 x 51 mm)
C2D-04
5/8”
(16 mm)
1”
(25 mm)
1-3/4”
(45 mm)
C2T-05 2” x 2”
(51 x 51 mm)
C2D-05
3/4”
(19 mm)
1-1/8”
(29 mm)
2”
(51 mm)
C2T-06 2” x 2”
(51 x 51 mm)
C2D-06
7/8”
(22 mm)
1-1/4”
(32 mm)
2-1/4”
(57 mm)
C2T-07 3” x 3”
(76 x 76 mm)
C2D-07
1”
(25 mm)
1-1/2”
(38 mm)
3”
(76 mm)
C2T-08 3” x 3”
(76 x 76 mm)
C2D-08
1-1/8”
(29 mm)
1-5/8”
(41 mm)
3-1/2”
(89 mm)
C2T-09 3” x 3”
(76 x 76 mm)
C2D-09
1-1/4”
(32 mm)
1-7/8”
(48 mm)
3-3/4”
(95 mm)
C2T-10 3” x 3”
(76 x 76 mm)
C2D-10
1-3/8”
(35 mm)
2-1/8”
(54 mm)
4”
(102 mm)
C2T-11 3” x 3”
(76 x 76 mm)
C2D-11
1-1/2”
(38 mm)
2-1/4”
(57 mm)
5”
(127 mm)
C2T-12 3” x 3”
(76 x 76 mm)
C2D-12
1-3/4”
(45 mm)
2-1/2”
(64 mm)
5-1/2”
(140 mm)
C2T-14 4” x 4”
(102 x 102 mm)
C2D-14
1-7/8”
(48 mm)
2-7/8”
(73 mm)
6”
(152 mm)
C2T-15
2”
(51 mm)
3”
(76 mm)
6”
(152 mm)
C2T-16
2-1/4”
(57 mm)
3-1/2”
(89 mm)
8”
(203 mm)
C2T-18

 

H1F Heavy Duty Hex Nuts

High Tensile NC Threaded Bar

Bar
Diameter
Across
Flats
Across
Corners
Thickness Part
Number
1/4”
(6.4 mm)
1/2”
(13 mm)
0.6”
(15 mm)
15/64”
(6 mm)
H1F-02
3/8”
(9.5 mm)
11/16”
(18 mm)
0.8”
(20 mm)
23/64”
(9 mm)
H1F-03
1/2”
(13 mm)
7/8”
(22 mm)
1.0”
(26 mm)
31/64”
(12 mm)
H1F-04
5/8”
(16 mm)
1-1/16”
(27 mm)
1.2”
(31 mm)
39/64”
(16 mm)
H1F-05
3/4”
(19 mm)
1-1/4”
(32 mm)
1.4”
(37 mm)
47/64”
(19 mm)
H1F-06
7/8”
(22 mm)
1-7/16”
(37 mm)
1.7”
(42 mm)
55/64”
(22 mm)
H1F-07
1”
(25 mm)
1-5/8”
(41 mm)
1.9”
(48 mm)
63/64”
(25 mm)
H1F-08
1-1/8”
(29 mm)
1-13/16”
(46 mm)
2.1”
(53 mm)
1-7/64”
(28 mm)
H1F-09
1-1/4”
(32 mm)
2”
(51 mm)
2.3”
(59 mm)
1-7/32”
(31 mm)
H1F-10
1-3/8”
(36 mm)
2-3/16”
(56 mm)
2.5”
(64 mm)
1-11/32”
(34 mm)
H1F-11
1-1/2”
(38 mm)
2-3/8”
(60 mm)
2.7”
(70 mm)
1-15/32”
(37 mm)
H1F-12
1-3/4”
(43 mm)
2-3/4”
(70 mm)
3.18”
(81 mm)
1-23/32”
(44 mm)
H1F-14
1-7/8”
(48 mm)
2-15/16”
(75 mm)
3.4”
(86 mm)
1-27/32”
(47 mm)
H1F-15
2”
(51 mm)
3-1/8”
(79 mm)
3.6”
(92 mm)
1-31/32”
(50 mm)
H1F-16
2-1/4”
(57 mm)
3-1/2”
(89 mm)
4”
(103 mm)
2-1/4”
(57 mm)
H1F-18

R9F Hardened Washers

High Tensile NC Threaded Bar

Bar
Diameter
Outside
Diameter
Inside
Diameter
Thickness Part
Number
1/4”
(6.4 mm)
5/8”
(16 mm)
9/32”
(7 mm)
1/16”
(1.5 mm)
R9F-02-436
3/8”
(9.5 mm)
1”
(25 mm)
7/16”
(11 mm)
5/64”
(2 mm)
R9F-03-436
1/2”
(13 mm)
1-1/16”
(27 mm)
9/16”
(14 mm)
9/64”
(3.56 mm)
R9F-04-436
5/8”
(16 mm)
1-3/4”
(45 mm)
11/16”
(17 mm)
9/64”
(3.6 mm)
R9F-05-436
3/4”
(19 mm)
1-15/32”
(37 mm)
13/16”
(21 mm)
9/64”
(3.6 mm)
R9F-06-436
7/8”
(22 mm)
1-3/4”
(45 mm)
15/16”
(24 mm)
5/32”
(4 mm)
R9F-07-436
1”
(25 mm)
2”
(51 mm)
1-1/8”
(29 mm)
5/32”
(4 mm)
R9F-08-436
1-1/8”
(29 mm)
2-1/4”
(57 mm)
1-1/4”
(32 mm)
5/32”
(4 mm)
R9F-09-436
1-1/4”
(32 mm)
2-1/2”
(64 mm)
1-3/8”
(35 mm)
5/32”
(4 mm)
R9F-10-436
1-3/8”
(36 mm)
2-3/4”
(70 mm)
1-1/2”
(38 mm)
5/32”
(4 mm)
R9F-11-436
1-1/2”
(38 mm)
3”
(76 mm)
1-5/8”
(41 mm)
5/32”
(4 mm)
R9F-12-436
1-3/4”
(43 mm)
3-3/8”
(86 mm)
1-7/8”
(48 mm)
7/32”
(5.6 mm)
R9F-14-436
1-7/8”
(48 mm)
3-3/4”
(95 mm)
2-1/8”
(54 mm)
7/32”
(5.6 mm)
R9F-16-436
2”
(51 mm)
3-3/4”
(95 mm)
2-1/8”
(54 mm)
7/32”
(5.6 mm)
R9F-16-436
2-1/4”
(57 mm)
4”
(102 mm)
2-3/8”
(60 mm)
9/32”
(7 mm)
R9F-18-436

R8M Beveled Washers

High Tensile NC Threaded Bar

Bar
Diameter
Outside
Diameter
Inside
Diameter
Thickness Part
Number
1/4”
(6.4 mm)
5/8”
(16 mm)
9/32”
(7 mm)
1/16”
(1.5 mm)
R9F-02-436
3/8”
(9.5 mm)
1”
(25 mm)
7/16”
(11 mm)
5/64”
(2 mm)
R9F-03-436
1/2”
(13 mm)
1-1/16”
(27 mm)
9/16”
(14 mm)
9/64”
(3.56 mm)
R9F-04-436
5/8”
(16 mm)
1-3/4”
(45 mm)
11/16”
(17 mm)
9/64”
(3.6 mm)
R9F-05-436
3/4”
(19 mm)
1-15/32”
(37 mm)
13/16”
(21 mm)
9/64”
(3.6 mm)
R9F-06-436
7/8”
(22 mm)
1-3/4”
(45 mm)
15/16”
(24 mm)
5/32”
(4 mm)
R9F-07-436
1”
(25 mm)
2”
(51 mm)
1-1/8”
(29 mm)
5/32”
(4 mm)
R9F-08-436
1-1/8”
(29 mm)
2-1/4”
(57 mm)
1-1/4”
(32 mm)
5/32”
(4 mm)
R9F-09-436
1-1/4”
(32 mm)
2-1/2”
(64 mm)
1-3/8”
(35 mm)
5/32”
(4 mm)
R9F-10-436
1-3/8”
(36 mm)
2-3/4”
(70 mm)
1-1/2”
(38 mm)
5/32”
(4 mm)
R9F-11-436
1-1/2”
(38 mm)
3”
(76 mm)
1-5/8”
(41 mm)
5/32”
(4 mm)
R9F-12-436
1-3/4”
(43 mm)
3-3/8”
(86 mm)
1-7/8”
(48 mm)
7/32”
(5.6 mm)
R9F-14-436
1-7/8”
(48 mm)
3-3/4”
(95 mm)
2-1/8”
(54 mm)
7/32”
(5.6 mm)
R9F-16-436
2”
(51 mm)
3-3/4”
(95 mm)
2-1/8”
(54 mm)
7/32”
(5.6 mm)
R9F-16-436
2-1/4”
(57 mm)
4”
(102 mm)
2-3/8”
(60 mm)
9/32”
(7 mm)
R9F-18-436

To achieve full strength of the nut, beveled washers must be used in conjunction with a hardened washer.

globe
Want to talk? Find your Williams Form Engineering Representative.
globe