Grade 100 All-Thread-Rebar
| Bar Designation Nominal Diameter & Pitch |
Minimum Net Area Thru Threads |
Minimum Ultimate Strength |
Minimum Yield Strength |
Nominal Weight |
Approx. Thread Major Dia. |
Part Number |
|---|---|---|---|---|---|---|
| #14 – 1-3/4” – 3-1/4 (43 mm) |
2.25 in2 (1452 mm2) |
258 kips (1148 kN) |
225 kips (1001 kN) |
8.18 lbs/ft (12.2 kg/m) |
1-7/8” (48 mm) |
R31-14 |
| #18 – 2-1/4” – 3-1/4 (57 mm) |
4.00 in2 (2581 mm2) |
460 kips (2046 kN) |
400 kips (1779 kN) |
13.6 lbs/ft (19.6 kg/m) |
2-3/8” (60 mm) |
R31-18 |
| #20 – 2-1/2” – 3 (64 mm) * |
4.91 in2 (3168 mm2) |
564 kips (2509 kN) |
491 kips (2184 kN) |
16.7 lbs/ft (24.8 kg/m) |
2-5/8” (67 mm) |
R31-20 |
Contact your Williams representative for other size availability.
Structural Properties
| Minimum Yield |
Ultimate Tensile |
|---|---|
| 100 KSI (689 MPa) |
115 KSI (793 MPa) |
Threads
Williams Grade 100 All-Thread Rebar has a cold rolled, continuous, rounded course thread form. Because of the full 360º concentric thread form, Williams All-Thread Rebar should only be bent under special provisions. Williams special thread (deformation) pattern projects ultra high relative rib area at 3 times that of conventional rebar. This provides for superior bond performance in concrete. Threads are available in both right and left hand.
Sizes
Grade 100 All-Thread Rebar is available in 3 diameters from #14 (43 mm) through #20 (64 mm). Other diameters can be provided upon special order. All diameters are available in continuous lengths up to 50’ (15.2 m). Check with your local WFEC Technical Rep for information on availability and lead times.
Welding
Welding of Grade 100 All-Thread Rebar should be approached with caution since no specific provisions have been included to enhance its weldability. Refer to ANSI/AWS D1.4 for proper selections and procedures.
Grade 100 All-Thread Rebar Accessories
All Couplings and Hex Nuts exceed 100% of the bar’s published ultimate strength.
Grade 100 All-Thread-Rebar Rebar Couplers
| Bar Desig. & Nominal Dia. |
Outside Diameter |
Thickness | Part Number |
|---|---|---|---|
| #14 – 1-3/4” (43 mm) |
2-3/4” (70 mm) |
6-1/2” (165 mm) |
R32-14 |
| #18 – 2-1/4” (57 mm) |
3-1/2” (89 mm) |
8” (203 mm) |
R32-18 |
| #20 – 2-1/2” (64 mm) |
4” (102 mm) |
8-1/2” (216 mm) |
R32-20 |
Grade 100 All-Thread-Rebar Rebar Hex Nuts
| Bar Desig. & Nominal Dia. |
Across Flats |
Across Corners |
Thickness | Part Number |
|---|---|---|---|---|
| #14 – 1-3/4” (43 mm) |
2-3/4” (70 mm) |
3.18” (81 mm) |
3” (76 mm) |
R33-14 |
| #18 – 2-1/4” (57 mm) |
3-3/4” (95 mm) |
4.04” (103 mm) |
3-3/4” (95 mm) |
R33-18 |
| #20 – 2-1/2” (64 mm) |
4” (102 mm) |
4.62” (117 mm) |
3-3/4” (95 mm) |
R33-20 |
Grade 100 All-Thread-Rebar Rebar Hardened Washers
| Bar Desig. & Nominal Dia. |
Outside Diameter |
Inside Diameter |
Thickness | Part Number |
|---|---|---|---|---|
| #14 – 1-3/4” (43 mm) |
3-3/8” (86 mm) |
1-7/8” (48 mm) |
7/32” (5.6 mm) |
R9F-14-436 |
| #18 – 2-1/4” (57 mm) |
4-1/2” (114 mm) |
2-5/8” (67 mm) |
9/32” (7 mm) |
R9F-20-436 |
| #20 – 2-1/2” (64 mm) |
5” (127 mm) |
2-7/8” (73 mm) |
9/32” (7 mm) |
R9F-22-436 |
Grade 100 All-Thread-Rebar Rebar Jam Nuts
Jam Nuts can not be substituted for full strength nuts. Standard rounded collar jam nut, with special order machined hex available.
| Bar Desig. & Nominal Dia. |
Across Flats |
Outer Diameter |
Thickness | Part Number |
|---|---|---|---|---|
| #14 – 1-3/4” (43 mm) |
2-3/4” (70 mm) |
3” (76 mm) |
1.44” (37 mm) |
R34-14JN |
| #18 – 2-1/4” (57 mm) |
3-1/4” (83 mm) |
3-1/2” (89 mm) |
1.56” (40 mm) |
R34-18JN |
| #20 – 2-1/2” (64 mm) |
3-3/4” (95 mm) |
4” (102 mm) |
1.75” (45 mm) |
R34-20JN |
