R1H Hollow-Core Spin-Lock Concrete Anchors
Through years of development Williams has produced and patented the Prestressable, Hollow-Core, Groutable Spin-Lock Concrete Anchoring Systems. The hollow-core allows the anchor to always be grouted from the lowest gravitational point. In an up-bolting situation, the grout is pumped in through the plastic grout tube and begins to fill the drill hole from the plate. The grout rises until the entire hole is filled and the grout returns through the hollow bar. In down grouting situations, the grout is pumped through the hollow bar and starts at the bottom of the hole. Grout rises and returns through the de-air tube when the hole is filled. Improperly or incomplete grouted anchors are subjected to relaxation and corrosion. Because the Spin-Lock head assembly provides 300º perimeter expansion anchorage and develops the full strength of the rod, the hollow-core concrete anchor may be prestressed to the desired load and tested prior to grouting. Unfortunately, the Hollow-Core rebar is not available from a domestic source.
R1H Structural Properties
| Yield Stress |
Ultimate Stress |
Elongation in 2” (51 mm) |
Reduction of Area |
|---|---|---|---|
| 91 KSI (627 MPa) |
124 KSI (854 MPa) |
15% min | 40% min |
R1H High Grade Hollow-Core Concrete Anchor
ASTM A615 Deformation Pattern
| Diameter & Threads per Inch |
Yield Strength (fy) |
Ultimate Strength (fu) |
Drill Hole Diameter (1) |
Type Head Assembly |
Torque (ft-lbs) | Minimum Embedment (3000 PSI – f’c) (5) |
Minimum Embedment (6500 PSI – f’c) (5) |
Part Number |
|
|---|---|---|---|---|---|---|---|---|---|
| To Expand Shell (2) |
On Nut for Tension (3) |
||||||||
| 1” – 8 (25 mm) |
48.6 kips (216 kN) |
66.3 kips (294 kN) |
1-3/4” (44 mm) |
C 14 | 250 ft-lbs (450*) |
400 ft-lbs | 17” (432 mm) |
13” (330 mm) |
R1H08C14 |
| 1-3/8” – 8 (35 mm) |
101 kips (451 kN) |
138 kips (615 kN) |
2-1/2” (65 mm) |
B 20 | 750 ft-lbs (1200*) |
Note (4) | 28” (711 mm) |
21” (533 mm) |
R1H11B20 |
| 2” – 6 (51 mm) |
221 kips (982 kN) |
301 kips (1338 kN) |
3-1/2” (89 mm) |
C 28 | 1000 ft-lbs (2000*) |
Note (4) | 46” (1168 mm) |
36” (914 mm) |
R1H16C28 |
(*) Do not exceed these numbers
(1) Care should be taken to drill a straight and properly sized hole.
(2) More torque may be required on long anchors or if the head assembly is next to rebar. Consult your Williams Representative for more specific details.
(3) Torque value listed will achieve approximate load of 50% of the anchor ultimate strength, and is based on the torque tension curves here.
(4) Stress to desired tensile load using a hollow ram hydraulic jack. Consult your Williams Representative.
(5) Full ultimate strength of anchor can be achieved at listed embedment depth, provided there are no edge or spacing effects on the anchor.
– Spin-Locks come standard with 12” of threaded area. Other lengths available upon request.
– WILLIAMS reserves the right to ship full length or coupled units as necessary.
Head Assemblies
The Williams Spin-Lock anchor assembly gives full 300° bearing area. The smooth shell design allows for maximum shell to concrete contact and eliminates “point of contact” created by serrated designs. The cone design supports the shell 300°, thereby eliminating any possible collapse of the shell under high load conditions. The thrust ring stop in front of the shell prevents any possible rebound of the expanded shell down the cone when subjected to nearby blasting. The Williams Spin-Lock anchor has been field proven on the world’s largest projects to far exceed in tension capacity any other mechanical anchor on the market.
| Head Assembly |
Drill Hole Diameter |
Diameter & Threads per Inch |
Cone | Shell | Thrust Ring | Slip Rings |
Overall Assembly Length |
|||
|---|---|---|---|---|---|---|---|---|---|---|
| Length | Part No. | Length | Part No. | Diameter | Thickness | |||||
| B20 | 2-1/2” (65 mm) |
1-3/8” – 8 NC (35 mm) |
4” (102 mm) |
LC-250 | 4” (102 mm) |
LS-250 | 2-1/8” (54 mm) |
1-3/8” (35 mm) |
9/64” (3.6 mm) |
9-5/8” (244 mm) |
| C14 | 1-3/4” (44 mm) |
1” – 8 NC (25 mm) |
4-1/4” (108 mm) |
LCF-175-8 | 3-3/4” (95 mm) |
LS-175 | 1-5/8” (41 mm) |
1-1/2” (38 mm) |
1/16” (1.6 mm) |
9-5/8” (244 mm) |
| C28 | 3-1/2” (89 mm) |
2” – 6 UN (51 mm) |
7” (178 mm) |
LCF-350-16 | 6” (152 mm) |
LS-350 | 2-7/8” (73 mm) |
2” (51 mm) |
1/8” (3.2 mm) |
15-1/4” (387 mm) |
Coupled Head Assemblies
Williams can manufacture Spin-Lock Anchor systems with the use of a transition coupling, which allows the anchor to be designed with a continuously workable thread-form. This is advantageous when the anchor length may need to be adjusted in the field due to variable site conditions. The transition coupling engages a continuously threaded U.N. bar into the head assembly and the All-Thread Bar (typically Grade 75 & Grade 80 All-Thread Rebar or 150 KSI All-Thread-Bar) is attached to the other end of the coupling.
C2T Stop-Type Couplings & C2D Flange Couplings
| Bar Diameter |
Outside Diameter |
Overall Length |
Stop-Type Part Number |
Flange Coupling | |
|---|---|---|---|---|---|
| Flange Size | Part Number | ||||
| 1” (25 mm) |
1-1/2” (38 mm) |
3” (76 mm) |
C2T-08 | 3” x 3” (76 x 76 mm) |
C2D-08 |
| 1-3/8” (35 mm) |
2-1/8” (54 mm) |
4” (102 mm) |
C2T-11 | 3” x 3” (76 x 76 mm) |
C2D-11 |
| 2” (51 mm) |
3” (76 mm) |
6” (152 mm) |
C2T-16 | – | – |
H1F Heavy Duty Hex Nuts
| Bar Diameter |
Across Flats |
Across Corners |
Thickness | Part Number |
|---|---|---|---|---|
| 1” (25 mm) |
1-5/8” (41 mm) |
1.9” (48 mm) |
63/64” (25 mm) |
H1F-08 |
| 1-3/8” (36 mm) |
2-3/16” (56 mm) |
2.5” (64 mm) |
1-11/32” (34 mm) |
H1F-11 |
| 2” (51 mm) |
3-1/8” (79 mm) |
3.6” (92 mm) |
1-31/32” (50 mm) |
H1F-16 |
R9F Hardened Washers
| Bar Diameter |
Outside Diameter |
Inside Diameter |
Thickness | Part Number |
|---|---|---|---|---|
| 1” (25 mm) |
2” (51 mm) |
1-1/16” (29 mm) |
5/32” (4 mm) |
R9F-08-436 |
| 1-3/8” (36 mm) |
2-3/4” (70 mm) |
1-1/2” (38 mm) |
5/32” (4 mm) |
R9F-11-436 |
| 2” (51 mm) |
3-3/4” (95 mm) |
2-1/8” (54 mm) |
7/32” (5.6 mm) |
R9F-16-436 |
R8M Beveled Washers
| Bar Diameter |
Degree of Bevel |
Outside Diameter |
Inside Diameter |
Maximum Thickness |
Minimum Thickness |
Part Number |
|---|---|---|---|---|---|---|
| 1” (25 mm) |
15° | 2-1/16” (52 mm) |
1” (25 mm) |
3/4” (19 mm) |
1/4” (6 mm) |
R8M-08S |
| 1-3/8” (36 mm) |
15° | 3-3/8” (86 mm) |
1-9/16” (40 mm) |
1-15/64” (31 mm) |
3/8” (9.5 mm) |
R8M-12S |
| 2” (51 mm) |
5° | 3-9/16” (91 mm) |
2-1/16” (52 mm) |
13/16” (21 mm) |
1/2” (13 mm) |
R8M-16 |
To achieve full strength of the nut, beveled washers must be used in conjunction with a hardened washer.
