B7S Coil All-Thread Spin-Lock Concrete Anchor
Williams B7S Coil All-Thread Spin-Lock Concrete Anchor utilizes an ASTM A108 Grade C1045 steel which provides high strength capacity and has the advantage of utilizing a more common steel for greater availability.
B7S Structural Properties
| Diameter Range |
Yield Stress |
Ultimate Stress |
Elongation in 2” Gauge Length |
Reduction of Area |
|---|---|---|---|---|
| 1/2” to 1” (13 to 25 mm) |
92 KSI (634 MPa) |
120 KSI (827 MPa) |
11% min | 20% min |
| 1-1/8” and up (29 mm) |
81 KSI (558 MPa) |
105 KSI (723 MPa) |
11% min | 20% min |
Meets strength of ASTM A325
B7S Coil All-Thread Spin-Lock Concrete Anchor
ASTM A108 Grade C1045
| Diameter & Threads per Inch |
Yield Strength (fy) |
Ultimate Strength (fu) |
Drill Hole Diameter (1) |
Type Head Assembly |
Torque (ft-lbs) | Minimum Embedment (3000 PSI – f’c) (5) |
Minimum Embedment (6500 PSI – f’c) (5) |
Part Number |
|
|---|---|---|---|---|---|---|---|---|---|
| To Expand Shell (2) |
On Nut for Tension (3) |
||||||||
| 1/2” – 13 (13 mm) |
13 kips (57.8 kN) |
17 kips (75.6 kN) |
1-1/4” (32 mm) |
A 10 | 50 ft-lbs (70*) |
85 ft-lbs | 7” (178 mm) |
5” (127 mm) |
B7S04A10 |
| 5/8” – 11 (16 mm) |
20.8 kips (92.5 kN) |
27.1 kips (121 kN) |
1-1/4” (32 mm) |
A 10 | 125 ft-lbs (250*) |
125 ft-lbs | 9” (229 mm) |
7” (178 mm) |
B7S05A10 |
| 3/4” – 10 (19 mm) |
30.7 kips (137 kN) |
40.0 kips (178 kN) |
1-3/4” (44 mm) |
C 14 | 210 ft-lbs (250*) |
210 ft-lbs | 11” (279 mm) |
9” (229 mm) |
B7S06C14 |
| 7/8” – 9 (22 mm) |
42.5 kips (189 kN) |
55.4 kips (246 kN) |
1-3/4” (44 mm) |
C 14 | 390 ft-lbs (410*) |
390 ft-lbs | 14” (356 mm) |
11” (279 mm) |
B7S07C14 |
| 1” – 8 (25 mm) |
55.7 kips (248 kN) |
72.7 kips (323 kN) |
1-3/4” (44 mm) |
C 14 | 500 ft-lbs (600*) |
550 ft-lbs | 17” (432 mm) |
13” (330 mm) |
B7S08C14 |
| 1-1/8” – 7 (29 mm) |
61.8 kips (275 kN) |
80.1 kips (356 kN) |
2-1/4” (57 mm) |
C 18 | 550 ft-lbs (600*) |
770 ft-lbs | 18” (457 mm) |
14” (356 mm) |
B7S09C18 |
| 1-1/4” – 7 (32 mm) |
78.5 kips (349 kN) |
102 kips (452 kN) |
2-1/4” (57 mm) |
C 18 | 750 ft-lbs (1200*) |
1000 ft-lbs | 21” (533 mm) |
16” (406 mm) |
B7S10C18 |
| 1-1/2” – 6 (38 mm) |
114 kips (506 kN) |
148 kips (656 kN) |
3” (76 mm) |
B 24 | 1000 ft-lbs (1700*) |
Note (4) | 27” (686 mm) |
21” (533 mm) |
B7S12B24 |
(*) Do not exceed these numbers
(1) Care should be taken to drill a straight and properly sized hole.
(2) More torque may be required on long anchors or if the head assembly is next to rebar. Consult your Williams Representative for more specific details.
(3) Torque value listed will achieve approximate load of 50% of the anchor ultimate strength, and is based on the torque tension curves here.
(4) Stress to desired tensile load using a hollow ram hydraulic jack. Consult your Williams Representative.
(5) Full ultimate strength of anchor can be achieved at listed embedment depth, provided there are no edge or spacing effects on the anchor.
– Spin-Locks come standard with 12” of threaded area. Other lengths available upon request.
– WILLIAMS reserves the right to ship full length or coupled units as necessary.
Head Assemblies
The Williams Spin-Lock anchor assembly gives full 300° bearing area. The smooth shell design allows for maximum shell to concrete contact and eliminates “point of contact” created by serrated designs. The cone design supports the shell 300°, thereby eliminating any possible collapse of the shell under high load conditions. The thrust ring stop in front of the shell prevents any possible rebound of the expanded shell down the cone when subjected to nearby blasting. The Williams Spin-Lock anchor has been field proven on the world’s largest projects to far exceed in tension capacity any other mechanical anchor on the market.
| Head Assembly |
Drill Hole Diameter |
Diameter & Threads per Inch |
Cone | Shell | Thrust Ring | Slip Rings |
Overall Assembly Length |
|||
|---|---|---|---|---|---|---|---|---|---|---|
| Length | Part No. | Length | Part No. | Diameter | Thickness | |||||
| A10 | 1-1/4” (32 mm) |
1/2” – 13 NC (13 mm) |
1-7/8” (48 mm) |
SC-114-4 | 1-7/8” (48 mm) |
SS-114 | 1-1/8” (29 mm) |
9/16” (14 mm) |
1/16” (1.6 mm) |
4-7/16” (112 mm) |
| 5/8” – 11 NC (16 mm) |
1-7/8” (48 mm) |
SC-114-5 | 1-7/8” (48 mm) |
SS-114 | 1-1/8” (29 mm) |
9/16” (14 mm) |
1/16” (1.6 mm) |
4-7/16” (112 mm) |
||
| B24 | 3” (76 mm) |
1-1/2” – 6 NC (38 mm) |
5-1/2” (140 mm) |
LC-300 | 5-1/2” (140 mm) |
LS-300 | 2-3/4” (70 mm) |
1-1/2” (38 mm) |
1/2” (12.7 mm) |
12-7/8” (325 mm) |
| C14 | 1-3/4” (44 mm) |
3/4” – 10 NC (19 mm) |
4-1/4” (108 mm) |
LCF-175-6 | 3-3/4” (95 mm) |
LS-175 | 1-5/8” (41 mm) |
1-1/4” (32 mm) |
1/16” (1.6 mm) |
9-3/8” (238 mm) |
| 7/8” – 9 NC (22 mm) |
4-1/4” (108 mm) |
LCF-175-7 | 3-3/4” (95 mm) |
LS-175 | 1-5/8” (41 mm) |
1-3/8” (35 mm) |
1/16” (1.6 mm) |
9-1/2” (241 mm) |
||
| 1” – 8 NC (25 mm) |
4-1/4” (108 mm) |
LCF-175-8 | 3-3/4” (95 mm) |
LS-175 | 1-5/8” (41 mm) |
1-1/2” (38 mm) |
1/16” (1.6 mm) |
9-5/8” (244 mm) |
||
| C18 | 2-1/4” (57 mm) |
1-1/8” – 7 NC (30 mm) |
4-7/8” (124 mm) |
LCF-225-9 | 4” (102 mm) |
LS-225 | 2” (51 mm) |
1-1/4” (32 mm) |
1/16” (1.6 mm) |
10-1/4” (260 mm) |
| 1-1/4” – 7 NC (32 mm) |
4-7/8” (124 mm) |
LCF-225-10 | 4” (102 mm) |
LS-225 | 2” (51 mm) |
1-1/4” (32 mm) |
1/16” (1.6 mm) |
10-1/4” (260 mm) |
||
Coupled Head Assemblies
Williams can manufacture Spin-Lock Anchor systems with the use of a transition coupling, which allows the anchor to be designed with a continuously workable thread-form. This is advantageous when the anchor length may need to be adjusted in the field due to variable site conditions. The transition coupling engages a continuously threaded U.N. bar into the head assembly and the All-Thread Bar (typically Grade 75 & Grade 80 All-Thread Rebar or 150 KSI All-Thread-Bar) is attached to the other end of the coupling.
C2T Stop-Type Couplings & C2D Flange Couplings
| Bar Diameter |
Outside Diameter |
Overall Length |
Stop-Type Part Number |
Flange Coupling | |
|---|---|---|---|---|---|
| Flange Size | Part Number | ||||
| 1/2” (13 mm) |
3/4” (19 mm) |
1-1/2” (38 mm) |
C2T-04 | 2” x 2” (51 x 51 mm) |
C2D-04 |
| 5/8” (16 mm) |
1” (25 mm) |
1-3/4” (45 mm) |
C2T-05 | 2” x 2” (51 x 51 mm) |
C2D-05 |
| 3/4” (19 mm) |
1-1/8” (29 mm) |
2” (51 mm) |
C2T-06 | 2” x 2” (51 x 51 mm) |
C2D-06 |
| 7/8” (22 mm) |
1-1/4” (32 mm) |
2-1/4” (57 mm) |
C2T-07 | 3” x 3” (76 x 76 mm) |
C2D-07 |
| 1” (25 mm) |
1-1/2” (38 mm) |
3” (76 mm) |
C2T-08 | 3” x 3” (76 x 76 mm) |
C2D-08 |
| 1-1/8” (29 mm) |
1-5/8” (41 mm) |
3-1/2” (89 mm) |
C2T-09 | 3” x 3” (76 x 76 mm) |
C2D-09 |
| 1-1/4” (32 mm) |
1-7/8” (48 mm) |
3-3/4” (95 mm) |
C2T-10 | 3” x 3” (76 x 76 mm) |
C2D-10 |
| 1-1/2” (38 mm) |
2-1/4” (57 mm) |
5” (127 mm) |
C2T-12 | 3” x 3” (76 x 76 mm) |
C2D-12 |
H1F Heavy Duty Hex Nuts
| Bar Diameter |
Across Flats |
Across Corners |
Thickness | Part Number |
|---|---|---|---|---|
| 1/2” (13 mm) |
7/8” (22 mm) |
1.0” (26 mm) |
31/64” (12 mm) |
H1F-04 |
| 5/8” (16 mm) |
1-1/16” (27 mm) |
1.2” (31 mm) |
39/64” (16 mm) |
H1F-05 |
| 3/4” (19 mm) |
1-1/4” (32 mm) |
1.4” (37 mm) |
47/64” (19 mm) |
H1F-06 |
| 7/8” (22 mm) |
1-7/16” (37 mm) |
1.7” (42 mm) |
55/64” (22 mm) |
H1F-07 |
| 1” (25 mm) |
1-5/8” (41 mm) |
1.9” (48 mm) |
63/64” (25 mm) |
H1F-08 |
| 1-1/8” (29 mm) |
1-13/16” (46 mm) |
2.1” (53 mm) |
1-7/64” (28 mm) |
H1F-09 |
| 1-1/4” (32 mm) |
2” (51 mm) |
2.3” (59 mm) |
1-7/32” (31 mm) |
H1F-10 |
| 1-1/2” (38 mm) |
2-3/8” (60 mm) |
2.7” (70 mm) |
1-15/32” (37 mm) |
H1F-12 |
R9F Hardened Washers
| Bar Diameter |
Outside Diameter |
Inside Diameter |
Thickness | Part Number |
|---|---|---|---|---|
| 1/2” (13 mm) |
1-1/16” (27 mm) |
17/32” (14 mm) |
9/64” (3.56 mm) |
R9F-04-436 |
| 5/8” (16 mm) |
1-5/16” (33 mm) |
11/16” (17 mm) |
9/64” (3.6 mm) |
R9F-05-436 |
| 3/4” (19 mm) |
1-7/16” (37 mm) |
13/16” (21 mm) |
9/64” (3.6 mm) |
R9F-06-436 |
| 7/8” (22 mm) |
1-3/4” (45 mm) |
15/16” (24 mm) |
5/32” (4 mm) |
R9F-07-436 |
| 1” (25 mm) |
2” (51 mm) |
1-1/16” (29 mm) |
5/32” (4 mm) |
R9F-08-436 |
| 1-1/8” (29 mm) |
2-1/4” (57 mm) |
1-3/16” (30 mm) |
5/32” (4 mm) |
R9F-09-436 |
| 1-1/4” (32 mm) |
2-1/2” (64 mm) |
1-3/8” (35 mm) |
5/32” (4 mm) |
R9F-10-436 |
| 1-1/2” (38 mm) |
3” (76 mm) |
1-5/8” (41 mm) |
5/32” (4 mm) |
R9F-12-436 |
R8M Beveled Washers
| Bar Diameter |
Degree of Bevel |
Outside Diameter |
Inside Diameter |
Maximum Thickness |
Minimum Thickness |
Part Number |
|---|---|---|---|---|---|---|
| 1/2” (13 mm) |
14° | 1-1/4” (32 mm) |
9/16” (14 mm) |
7/16” (11 mm) |
1/8” (3 mm) |
R8M-04 |
| 5/8” (16 mm) |
11° | 1-9/16” (40 mm) |
13/16” (21 mm) |
1/2” (13 mm) |
3/16” (5 mm) |
R8M-06 |
| 3/4” (19 mm) |
11° | 1-9/16” (40 mm) |
13/16” (21 mm) |
1/2” (13 mm) |
3/16” (5 mm) |
R8M-06 |
| 7/8” (22 mm) |
15° | 2-1/16” (52 mm) |
1” (25 mm) |
3/4” (19 mm) |
1/4” (6 mm) |
R8M-08S |
| 1” (25 mm) |
15° | 2-1/16” (52 mm) |
1” (25 mm) |
3/4” (19 mm) |
1/4” (6 mm) |
R8M-08S |
| 1-1/8” (29 mm) |
15° | 2-13/16” (71 mm) |
1-5/16” (33 mm) |
1” (25 mm) |
5/16” (8 mm) |
R8M-09S |
| 1-1/4” (32 mm) |
15° | 3-3/8” (86 mm) |
1-9/16” (40mm) |
1-15/64” (31 mm) |
3/8” (9.5 mm) |
R8M-12S |
| 1-1/2” (38 mm) |
15° | 3-1/2” (89 mm) |
1-3/4” (45 mm) |
1-1/4” (32mm) |
3/8” (9.5 mm) |
R8M-13S |
To achieve full strength of the nut, beveled washers must be used in conjunction with a hardened washer.
