S-9 Undercut Concrete Anchor

ASTM A193 Grade B7

Structural Properties

Yield
Stress
Ultimate
Stress
Elongation in
20 Bar Dia
Reduction
of Area
Charpy at
-40ᵒ F (-40ᵒ C)
105 KSI
(723 MPa)
125 KSI
(861 MPa)
16% min 50% min 20 ft/lbs
(27 Joules)

 

Diameter
& Threads
per Inch
Maximum
Factored
Design Load
Yield
Strength
(fy)
Ultimate
Strength
(fu)
Drill Hole
Diameter
Minimum
Embedment
(3000 PSI – f’c)
Minimum
Embedment
(6500 PSI – f’c)
Part
Number
1/4” – 20
(6.4 mm)
2.98 kips
(13.3 kN)
3.34 kips
(14.9 kN)
3.98 kips
(17.7 kN)
5/8”
(16 mm)
3”
(77 mm)
2”
(51 mm)
S9T-02
3/8” – 16
(9.5 mm)
7.27 kips
(32.3 kN)
8.14 kips
(36.2 kN)
9.69 kips
(43.1 kN)
7/8”
(22 mm)
5”
(127 mm)
4”
(102 mm)
S9T-03
1/2” – 13
(13 mm)
13.3 kips
(59.2 kN)
14.9 kips
(66.3 kN)
17.7 kips
(78.9 kN)
7/8”
(22 mm)
8”
(204 mm)
6”
(153 mm)
S9T-04
5/8” – 11
(16 mm)
21.2 kips
(94.2 kN)
23.7 kips
(105 kN)
28.2 kips
(125 kN)
1-1/8”
(29 mm)
10”
(254 mm)
8”
(204 mm)
S9T-05
3/4” – 10
(19 mm)
31.3 kips
(139 kN)
35.1 kips
(156 kN)
41.8 kips
(186 kN)
1-1/8”
(29 mm)
13”
(331 mm)
10”
(254 mm)
S9T-06
1” – 8
(25 mm)
56.8 kips
(253 kN)
63.6 kips
(283 kN)
75.8 kips
(337 kN)
1-5/8”
(41 mm)
19”
(483 mm)
15”
(381 mm)
S9T-08
1-1/4” – 7
(32 mm)
90.8 kips
(404 kN)
102 kips
(453 kN)
121 kips
(539 kN)
2”
(51 mm)
26”
(661 mm)
20”
(508 mm)
S9T-10
1-1/2” – 6
(38 mm)
132 kips
(586 kN)
148 kips
(656 kN)
176 kips
(781 kN)
2-1/2”
(64 mm)
33”
(839 mm)
25”
(635 mm)
S9T-12

These loads are valid where embedment is sufficient to assure steel failure; that is concrete shear cone strength is greater than steel strength. Minimum ultimate static tension values based on physicals of ASTM A193 Grade B7 bolting material having 125,000 PSI minimum ultimate strength.


C2T Stopy-Type & Flange Couplings

Bar
Diameter
Outside
Diameter
Overall
Length
Stop-Type
Part Number
Flange Coupling
Flange Size Part Number
1/4”
(6.4 mm)
1/2”
(13 mm)
7/8”
(22 mm)
C2T-02
3/8”
(9.5 mm)
3/4”
(19 mm)
1-1/2”
(38 mm)
C2T-03 2” x 2”
(51 x 51 mm)
C2D-03
1/2”
(13 mm)
3/4”
(19 mm)
1-1/2”
(38 mm)
C2T-04 2” x 2”
(51 x 51 mm)
C2D-04
5/8”
(16 mm)
1”
(25 mm)
1-3/4”
(45 mm)
C2T-05 2” x 2”
(51 x 51 mm)
C2D-05
3/4”
(19 mm)
1-1/8”
(29 mm)
2”
(51 mm)
C2T-06 2” x 2”
(51 x 51 mm)
C2D-06
7/8”
(22 mm)
1-1/4”
(32 mm)
2-1/4”
(57 mm)
C2T-07 3” x 3”
(76 x 76 mm)
C2D-07
1”
(25 mm)
1-1/2”
(38 mm)
3”
(76 mm)
C2T-08 3” x 3”
(76 x 76 mm)
C2D-08
1-1/8”
(29 mm)
1-5/8”
(41 mm)
3-1/2”
(89 mm)
C2T-09 3” x 3”
(76 x 76 mm)
C2D-09
1-1/4”
(32 mm)
1-7/8”
(48 mm)
3-3/4”
(95 mm)
C2T-10 3” x 3”
(76 x 76 mm)
C2D-10
1-3/8”
(35 mm)
2-1/8”
(54 mm)
4”
(102 mm)
C2T-11 3” x 3”
(76 x 76 mm)
C2D-11
1-1/2”
(38 mm)
2-1/4”
(57 mm)
5”
(127 mm)
C2T-12 3” x 3”
(76 x 76 mm)
C2D-12
1-3/4”
(45 mm)
2-1/2”
(64 mm)
5-1/2”
(140 mm)
C2T-14 4” x 4”
(102 x 102 mm)
C2D-14
1-7/8”
(48 mm)
2-7/8”
(73 mm)
6”
(152 mm)
C2T-15
2”
(51 mm)
3”
(76 mm)
6”
(152 mm)
C2T-16
2-1/4”
(57 mm)
3-1/2”
(89 mm)
8”
(203 mm)
C2T-18

H1F Heavy Duty Hex Nuts

Bar
Diameter
Across
Flats
Across
Corners
Thickness Part
Number
1/4”
(6.4 mm)
1/2”
(13 mm)
0.6”
(15 mm)
15/64”
(6 mm)
H1F-02
3/8”
(9.5 mm)
11/16”
(18 mm)
0.8”
(20 mm)
23/64”
(9 mm)
H1F-03
1/2”
(13 mm)
7/8”
(22 mm)
1.0”
(26 mm)
31/64”
(12 mm)
H1F-04
5/8”
(16 mm)
1-1/16”
(27 mm)
1.2”
(31 mm)
39/64”
(16 mm)
H1F-05
3/4”
(19 mm)
1-1/4”
(32 mm)
1.4”
(37 mm)
47/64”
(19 mm)
H1F-06
7/8”
(22 mm)
1-7/16”
(37 mm)
1.7”
(42 mm)
55/64”
(22 mm)
H1F-07
1”
(25 mm)
1-5/8”
(41 mm)
1.9”
(48 mm)
63/64”
(25 mm)
H1F-08
1-1/8”
(29 mm)
1-13/16”
(46 mm)
2.1”
(53 mm)
1-7/64”
(28 mm)
H1F-09
1-1/4”
(32 mm)
2”
(51 mm)
2.3”
(59 mm)
1-7/32”
(31 mm)
H1F-10
1-3/8”
(36 mm)
2-3/16”
(56 mm)
2.5”
(64 mm)
1-11/32”
(34 mm)
H1F-11
1-1/2”
(38 mm)
2-3/8”
(60 mm)
2.7”
(70 mm)
1-15/32”
(37 mm)
H1F-12
1-3/4”
(43 mm)
2-3/4”
(70 mm)
3.18”
(81 mm)
1-23/32”
(44 mm)
H1F-14
1-7/8”
(48 mm)
2-15/16”
(75 mm)
3.4”
(86 mm)
1-27/32”
(47 mm)
H1F-15
2”
(51 mm)
3-1/8”
(79 mm)
3.6”
(92 mm)
1-31/32”
(50 mm)
H1F-16
2-1/4”
(57 mm)
3-1/2”
(89 mm)
4”
(103 mm)
2-1/4”
(57 mm)
H1F-18

 

R9F Hardened Washers

Bar
Diameter
Outside
Diameter
Inside
Diameter
Thickness Part
Number
1/4”
(6.4 mm)
5/8”
(16 mm)
9/32”
(7 mm)
1/16”
(1.5 mm)
R9F-02-436
3/8”
(9.5 mm)
1”
(25 mm)
7/16”
(11 mm)
5/64”
(2 mm)
R9F-03-436
1/2”
(13 mm)
1-1/16”
(27 mm)
9/16”
(14 mm)
9/64”
(3.56 mm)
R9F-04-436
5/8”
(16 mm)
1-3/4”
(45 mm)
11/16”
(17 mm)
9/64”
(3.6 mm)
R9F-05-436
3/4”
(19 mm)
1-15/32”
(37 mm)
13/16”
(21 mm)
9/64”
(3.6 mm)
R9F-06-436
7/8”
(22 mm)
1-3/4”
(45 mm)
15/16”
(24 mm)
5/32”
(4 mm)
R9F-07-436
1”
(25 mm)
2”
(51 mm)
1-1/8”
(29 mm)
5/32”
(4 mm)
R9F-08-436
1-1/8”
(29 mm)
2-1/4”
(57 mm)
1-1/4”
(32 mm)
5/32”
(4 mm)
R9F-09-436
1-1/4”
(32 mm)
2-1/2”
(64 mm)
1-3/8”
(35 mm)
5/32”
(4 mm)
R9F-10-436
1-3/8”
(36 mm)
2-3/4”
(70 mm)
1-1/2”
(38 mm)
5/32”
(4 mm)
R9F-11-436
1-1/2”
(38 mm)
3”
(76 mm)
1-5/8”
(41 mm)
5/32”
(4 mm)
R9F-12-436
1-3/4”
(43 mm)
3-3/8”
(86 mm)
1-7/8”
(48 mm)
7/32”
(5.6 mm)
R9F-14-436
1-7/8”
(48 mm)
3-3/4”
(95 mm)
2-1/8”
(54 mm)
7/32”
(5.6 mm)
R9F-16-436
2”
(51 mm)
3-3/4”
(95 mm)
2-1/8”
(54 mm)
7/32”
(5.6 mm)
R9F-16-436
2-1/4”
(57 mm)
4”
(102 mm)
2-3/8”
(60 mm)
9/32”
(7 mm)
R9F-18-436

R8M Beveled Washers

Bar
Diameter
Outside
Diameter
Inside
Diameter
Thickness Part
Number
1/4”
(6.4 mm)
5/8”
(16 mm)
9/32”
(7 mm)
1/16”
(1.5 mm)
R9F-02-436
3/8”
(9.5 mm)
1”
(25 mm)
7/16”
(11 mm)
5/64”
(2 mm)
R9F-03-436
1/2”
(13 mm)
1-1/16”
(27 mm)
9/16”
(14 mm)
9/64”
(3.56 mm)
R9F-04-436
5/8”
(16 mm)
1-3/4”
(45 mm)
11/16”
(17 mm)
9/64”
(3.6 mm)
R9F-05-436
3/4”
(19 mm)
1-15/32”
(37 mm)
13/16”
(21 mm)
9/64”
(3.6 mm)
R9F-06-436
7/8”
(22 mm)
1-3/4”
(45 mm)
15/16”
(24 mm)
5/32”
(4 mm)
R9F-07-436
1”
(25 mm)
2”
(51 mm)
1-1/8”
(29 mm)
5/32”
(4 mm)
R9F-08-436
1-1/8”
(29 mm)
2-1/4”
(57 mm)
1-1/4”
(32 mm)
5/32”
(4 mm)
R9F-09-436
1-1/4”
(32 mm)
2-1/2”
(64 mm)
1-3/8”
(35 mm)
5/32”
(4 mm)
R9F-10-436
1-3/8”
(36 mm)
2-3/4”
(70 mm)
1-1/2”
(38 mm)
5/32”
(4 mm)
R9F-11-436
1-1/2”
(38 mm)
3”
(76 mm)
1-5/8”
(41 mm)
5/32”
(4 mm)
R9F-12-436
1-3/4”
(43 mm)
3-3/8”
(86 mm)
1-7/8”
(48 mm)
7/32”
(5.6 mm)
R9F-14-436
1-7/8”
(48 mm)
3-3/4”
(95 mm)
2-1/8”
(54 mm)
7/32”
(5.6 mm)
R9F-16-436
2”
(51 mm)
3-3/4”
(95 mm)
2-1/8”
(54 mm)
7/32”
(5.6 mm)
R9F-16-436
2-1/4”
(57 mm)
4”
(102 mm)
2-3/8”
(60 mm)
9/32”
(7 mm)
R9F-18-436

To achieve full strength of the nut, beveled washers must be used in conjunction with a hardened washer.

globe
Want to talk? Find your Williams Form Engineering Representative.
globe