Hydraulic Jacks for Threaded Bar Anchors

 

T7Z Open Frame Hydraulic Jacks

Used for testing and pre-stressing All-Thread-Bars. Available with up to 5-1/8” center hole. Unit comes with ram, pump, gauge, hoses, jack stand, high strength coupling, high strength test rod, plate, hex nut and knocker wrench

Jack
Capacity
Pump
Method
Ram
Height
Base
Size
Ram
Travel
Minimum
Total Ram
& Frame
Height
Maximum
Test Rod
Diameter
Ram
Area
Approx.
Total Ram
& Frame
Weight
10 tons
(89 kN)
Hand
Single Acting
5-5/16”
(135 mm)
3” Diameter
(76 mm)
2-1/2”
(64 mm)
8-3/8”
(213 mm)
3/4”
(19 mm)
2.12 in2
(14 cm2)
12 lbs
(5.4 kg)
30 tons
(267 kN)
Hand
Double Acting
6-1/16”
(154 mm)
8” x 8”
(203 x 203 mm)
3”
(76 mm)
19”
(483 mm)
1-1/4”
(32 mm)
5.89 in2
(38 cm2)
80 lbs
(36 kg)
60 tons
(534 kN)
Hand, Air, or Electric
Double Acting
9-1/2”
(241 mm)
9” x 9”
(228 x 228 mm)
5”
(127 mm)
29”
(737 mm)
2-1/8”
(54 mm)
12.31 in2
(79 cm2)
153 lbs
(69 kg)
60 tons
(534 kN)
Hand, Air, or Electric
Double Acting
12-3/4”
(324 mm)
9” x 9”
(228 x 228 mm)
6-1/2”
(165 mm)
32-1/4”
(737 mm)
2-1/8”
(54 mm)
12.73 in2
(82 cm2)
173 lbs
(78 kg)
100 tons
(890 kN)
Air or Electric
Double Acting
13-1/2”
(343 mm)
9” x 9”
(228 x 228 mm)
6”
(152 mm)
29-1/8”
(740 mm)
3-1/8”
(79 mm)
20.63 in2
(133 cm2)
198 lbs
(87 kg)
100 tons
(890 kN)
Air or Electric
Double Acting
12-3/8”
(314 mm)
9” x 9”
(228 x 228 mm)
6”
(152 mm)
28”
(711 mm)
2”
(51 mm)
20.03 in2
(129 cm2)
192 lbs
(87 kg)
150 tons
(1334 kN)
Air or Electric
Double Acting
12-1/4”
(311 mm)
12” x 12”
(305 x 305 mm)
5”
(127 mm)
32-1/4”
(819 mm)
2-1/2”
(64 mm)
30.1 in2
(194 cm2)
350 lbs
(159 kg)
200 tons
(1779 kN)
Air or Electric
Double Acting
12-1/4”
(311 mm)
12” x 12”
(305 x 305 mm)
8”
(203 mm)
34”
(864 mm)
4-1/16”
(103 mm)
40.45 in2
(261 cm2)
518 lbs
(235 kg)
200 tons
(1779 kN)
Air or Electric
Double Acting
27-1/2”
(699 mm)
12” x 12”
(305 x 305 mm)
15”
(381 mm)
49-1/4”
(1250 mm)
4”
(102 mm)
47.20 in2
(304 cm2)
604 lbs
(274 kg)
300 tons
(2670 kN)
Electric
Double Acting
27-1/2”
(699 mm)
15” Dia.
(381 mm)
15”
(381 mm)
50-1/2”
(1283 mm)
5-3/8”
(137 mm)
78.5 in2
(506 cm2)
1,400 lbs
(635 kg)
400 tons
(3558 kN)
Electric
Double Acting
18-3/4”
(476 mm)
15” Dia.
(381 mm)
6”
(152 mm)
45-3/4”
(1162 mm)
4-1/4”
(108 mm)
91.5 in2
(590 cm2)
1,300 lbs
(590 kg)

T80 Post-Tension Hydraulic Jacks

With the T80 series the enclosed bearing housing contains a geared socket drive to tighten the bolt hex nut during tensioning. Test jack housing will accommodate up to a 16” deep pocket (The 200 ton accommodates a 14-1/2” pocket.

Jack
Capacity
Pump
Method
Ram
Height
Base
Size
Ram
Travel
Minimum
Total Ram
& Frame
Height
Maximum
Test Rod
Diameter
Max.
150 KSI
Bar Size
Ram
Area
Approx.
Total Ram
& Fram
Weight
60 tons
(534 kN)
Hand, Air, or Electric
Double Acting
9-1/2”
(241 mm)
GearBox: 8.5” x 20.5”
(215 x 520 mm)
Cylinder: 3.63” Dia.
(92 mm Dia.)
5”
(127 mm)
33”
(838 mm)
2”
(51 mm)
1”
(25 mm)
12.31 in2
(79 cm2)
122 lbs
(55 kg)
60 tons
(534 kN)
Hand, Air, or Electric
Double Acting
12-3/4”
(324 mm)
6-1/2”
(165 mm)
36”
(914 mm)
2”
(51 mm)
1-1/4”
(25 mm)
12.73 in2
(82 cm2)
225 lbs
(102 kg)
100 tons
(890 kN)
Air or Electric
Double Acting
13-1/2”
(343 mm)
GearBox: 8.5” x 20.5”
(216 x 520 mm)
Cylinder: 4.63” Dia.
(118 mm Dia.)
6”
(152 mm)
39”
(990 mm)
3-1/8”
(79 mm)
1-3/8”
(35 mm)
20.63 in2
(133 cm2)
270 lbs
(123 kg)
150 tons
(1334 kN)
Air or Electric
Double Acting
12-1/4”
(311 mm)
5”
(127 mm)
28”
(965 mm)
2-1/2”
(64 mm)
1-3/8”
(35 mm)
30.1 in2
(194 cm2)
243 lbs
(110 kg)
200 tons
(1779 kN)
Air or Electric
Double Acting
16”
(406 mm)
Frame: 11”x11”x19.75”
Nose: 7” Dia.
8”
(203 mm)
43”
(1097 mm)
4”
(102 mm)
1-3/4”
(45 mm)
40.45 in2
(261 cm2)
455 lbs
(203 kg)

Torque Equipment

T8Z Hydraulic Torque Wrench

The hydraulic torque wrench is used for tensioning anchors in tight fitting locations where it would be difficult to use an hydraulic jack. The wrench is also recommended for use when setting the large diameter Spin-Lock anchors. The torque wrenches are light weight and can achieve a maximum of 7,400 ft-lbs. All Hydraulic TorqueWrenches have 1-1/2” square drive outputs.

Maximum
Torque
Length Height Weight
5,590 ft/lbs
(773 kg/M)
11”
(279 mm)
4.5”
(114 mm)
16.8 lbs
(7.6 kg)
7,400 ft/lbs
(1,023 kg/M)
10.74”
(273 mm)
7”
(178 mm)
19 lbs
(11.3 kg)

T8Z Torque Wrench

For applying torque to the anchor bolt when setting the anchor.

Bolt
Diameter
Square
Drive Size
Capacity
(ft. lbs.)
1/2”-1” 3/4” 100-600
*1-1/8”-2” 1” 200-1,000

T8Z-04 Torque Multiplier (4:1)

For use with T8Z Torque Wrench.Other sizes available.

Size Square
Drive
Input
Square
Drive
Output
Maximum
Torque
GA 186 1” 1-1/2” 4,000 (ft.lbs.)

T1Z &T2Z Long Fitting Tool Adapters

For driving hex nuts and setting tools, typically with our Spin-Lock anchor systems. Works with torque wrench or impact gun.Available with a 3/4”, 1” and 1-1/2” square drive.Please specify square drive for compatibility with your equipment.

[image] [image]


K3F-26 Long Fitting Wrench Adapter

Hex knocker wrench-es are used for safe hex nut adjustment inside of open frame jacks


T3Z Hex Knocker Wrench

Hex knocker wrench-es are used for safe hex nut adjustment inside of open frame jacks.


Spin Adapter

This tool provides a transition between the drill steel and the set-ting tool when the drilling equipment is used to spin the anchor bar through the resin cartridges.Adaptations to various drill steel types are available and must be specified when placing order.


 

T9F Impact Tool

Lightweight air impact guns for applying torque to anchor bolts when setting or tensioning the anchor assembly.

Size Bolt
Diameter
Square
Drive Size
Capacity
(ft/lbs)
T9F-08 1” to 1-3/8” 1” 1,700 – 2,000
T9F-12 1-3/8” to 2” 1-1/2” 3,000 – 4,000

 

S6Z Spin-Lock Setting Tool

This tool is required for torque setting theSpin-Lock anchors or for spinning rebars into resin cartridges without jamming or scoring the bolt threads. Special two-piece design allows lower hex to be held in place while upper hex is loosened for easy removal. Hardened steel allows for several reuses. Two piece design assures easy removal. Other thread forms are available for allWilliams anchors.

Bolt Rod
Diameter
Part
Number
1/2” S6Z-OH-004
5/8” S6Z-OH-005
3/4” S6Z-OH-006
7/8” S6Z-OH-007
1” S6Z-OH-008
1-1/8” S6Z-OH-009
1-1/4” S6Z-OH-010
1-3/8” S6Z-OH-011
1-1/2” S6Z-OH-012
1-3/4” S6Z-OH-014
1-7/8” S6Z-OH-015
2” S6Z-OH-016

 

R71 150 KSI All-Thread-Bar & R61 Grade 75 All-Thread Rebar Torque Tension Chart

All data based on greased (MolyKoat Gn) threads and surfaces.

 

 

Load in KipsLoad in KipsFor R1J bars use R1S values.For R1J bars use R1S values.R1H Hollow-Core, R1V High Impact, R1S High Tensile,R1J Solid Rebar & R7S 150 KSI Spin-Lock Torque Tension Chart

 

 

 

 

globe
Want to talk? Find your Williams Form Engineering Representative.
globe