|
|
|
Polyester Resin Anchor Installation Equipment
|
|
|
|
|
|
 |
|
|
|
|
|
 |
|
|
|
T6Z-04 Hand Powered Grout Pump
|
 |
2 stroke position, piston driven pump. Pump cement grout only, no sand. Use of plasticizer is recommend with hand pumps.
|
| Approximate size: |
30-3/4" high
24-1/4" wide
35" high w/ handle |
| Weight: |
60 lbs. (Dry weight) |
| Outlet Capacity: |
40 PSI average
80 PSI maximum |
|
|
|
|
|
|
|
|
T6Z-08 Air Powered Grout Pump
|
 |
| Pumps cement grout only, no sand. 32 Gallon Mixing Tank. Mixes up to 2 sacks of material at once and allows for grout to be pumped during mixing or mixed without pumping. |
| Approximate size: |
50" long
30.5" high
52" wide |
| Weight: |
560 lbs. |
| Production Rate: |
8 gallons per minute
at 150 psi |
|
|
|
|
|
|
|
|
|
| T6Z-02 Air Powered Grout Pump |
 |
|
Progressive cavity feed for continuous grout flow. Pumps cement grout only, no sand
|
| Approximate size: |
42" long 21" high 24" wide |
| Weight: |
170 lbs. w/o hose |
| Drive Power: |
90 - 150 psi or 130 cu.ft. of air per min. to develop 3 H.P. |
| Grout Outlet: |
3 to 4 gallons per minute of 0-120 psi |
| Capacity: |
6 gallon hopper |
|
|
|
|
|
|
|
|
|
|
|
 |
| The heavy duty, high volume Colloidal Grout Plant is favored for precision post-tension grouting. The unit features a high speed shear mixer that thoroughly wets each particle and discharges the mixed material into a 13 cubic foot capacity agitating holding tank. A direct coupled progressing cavity pump delivers slurries at a rate of up to 20 gpm and pressures of up to 261 psi. The unit easily mixes and pumps slurries of Portland cement, fly ash, bentonite, and lime flour. All controls are conveniently located on the operator platform for easy one-man control. |
| Pump |
Pump Type |
31.6 progressing cavity |
| Output/Preasure |
variable up to 20 gpm, 261 psi |
| Colloidal Mixer |
Mix Tank |
13.0 CF with bottom clean out |
| Mixing Pump |
2 x 3 x 6 diffuser-type centrifugal |
| Holding Tank |
13.0 paddle agitating |
| Drive Power |
Air |
300 CFM, 100 psi |
| Physical Specifications |
Dimensions |
96" L x 60" W x 63" H |
| Weight |
1800-2800 lbs. |
|
|
|
|
|
|
|
|
|
| T7Z Hydraulic Jacks |
 |
|
Used for testing and pre-stressing anchor bolts. Available with up to 5-1/8" center hole. Unit comes with ram, pump, gauge, hoses, jack stand, high strength coupling, high strength test rod, plate, hex nut and knocker wrench. Calibrations are available upon request.
Note: Jack pull rods should have a higher capacity than the anchor rod.
|
|
|
Jack
Capacity |
Pump
Method |
Ram
Height |
Base
Size |
Ram
Travel |
Minimum
Total
Height
of Ram
& Frame |
Maximum
Test Rod
Diameter |
Ram
Area |
Approx.
Total
Weight
of Ram
& Frame |
10 tons
(89 kN) |
Hand
Single Acting |
5-5/16"
(135 mm) |
3" Dia.
(76 mm) |
2-1/2"
(64 mm) |
8-3/8"
(213 mm) |
3/4"
(19 mm) |
2.12 in2
(1368 mm2) |
12 lbs.
(5.4 kg) |
|
30 tons
(267 kN)
|
Hand
Single Acting |
6-1/16"
(154 mm)
|
8" x 8"
(203 x 203 mm)
|
3"
(76 mm)
|
19"
(483 mm)
|
1-1/4"
(32 mm)
|
5.89 in2
(3800 mm2)
|
80 lbs.
(36 kg)
|
|
60 tons
(534 kN)
|
Hand, Air or Electric
Double Acting |
9-1/2"
(241 mm)
|
8" x 8"
(203 x 203 mm)
|
5"
(127 mm)
|
29"
(737 mm)
|
2"
(51 mm)
|
12.31 in2
(7942 mm2)
|
153 lbs.
(69 kg)
|
|
60 tons
(534 kN)
|
Hand, Air or Electric
Double Acting |
12-3/4"
(324 mm)
|
9" x 9"
(228 x 228 mm)
|
6-1/2"
(165 mm)
|
29"
(737 mm)
|
2"
(51 mm) |
12.73 in2
(8213 mm2)
|
225 lbs.
(102 kg)
|
|
100 tons
(890 kN)
|
Air or Electric
Double Acting
|
13-1/2"
(343 mm)
|
9" x 9"
(228 x 228 mm)
|
6"
(152 mm)
|
35"
(889 mm)
|
3-1/8"
(79 mm)
|
20.63 in2
(13310 mm2)
|
270 lbs.
(123 kg)
|
100 tons
(890 kN) |
Air or Electric
Double Acting |
12-3/8"
(314 mm)
|
9" x 9"
(228 x 228 mm)
|
6"
(152 mm)
|
28"
(711 mm)
|
2"
(51 mm)
|
20.03 in2
(12923 mm2)
|
192 lbs.
(87 kg)
|
|
150 tons
(1334 kN)
|
Air or Electric
Double Acting |
12-1/4"
(311 mm)
|
12" x 12"
(305 x 305 mm)
|
5"
(127 mm)
|
32-1/4"
(819 mm)
|
2-1/2"
(64 mm)
|
30.1 in2
(19419 mm2)
|
350 lbs.
(159 kg)
|
|
200 tons
(1779 kN)
|
Air or Electric
Double Acting
|
16"
(406 mm)
|
12" x 12"
(305 x 305 mm) |
8"
(203 mm)
|
34"
(864 mm)
|
4"
(102 mm)
|
40.45 in2
(26097 mm2)
|
518 lbs.
(235 kg)
|
|
400 tons
(3558 kN)
|
Electric
Double Acting |
18-3/4"
(476 mm)
|
15" Dia.
(381 mm)
|
6"
(152 mm)
|
45-3/4"
(1162 mm)
|
4-1/4"
(108 mm)
|
91.5 in2
(59032 mm2)
|
1300 lbs.
(590 kg)
|
400 tons
(3558 kN) |
Electric
Double Acting |
20-3/8"
(518 mm)
|
17" Dia.
(432 mm)
|
8"
(203 mm)
|
49"
(1245 mm)
|
5"
(127 mm)
|
118 in2
(76258 mm2)
|
1500 lbs.
(680 kg)
|
|
|
|
|
Certification of gauge accuracy available on request prior to shipment only. |
|
|
|
 |
|
|
|
|
|
|
|
|
T80 Post-Tensioning Jacks
|
 |
|
With the T80 series the enclosed bearing housing contains a geared socket drive to tighten the bolt hex nut during tensioning. Test jack housing will accommodate up to a 9” deep pocket.
|
|
|
Jack
Capacity |
Pump
Method |
Ram
Height |
Base
Size |
Ram
Travel |
Minimum
Total
Height
of Ram
& Frame |
Maximum
Test Rod
Diameter |
Ram
Area |
Approx.
Total
Weight
of Ram
& Frame |
|
60 tons
(534 kN)
|
Hand, Air or Electric
Double Acting |
9-1/2"
(241 mm)
|
Gear Box: 6.5" x 9.5"
(165 x 241 mm)
Cylinder Dia.: 3.63"
(92 mm)
|
5"
(127 mm)
|
30"
(762 mm)
|
2"
(51 mm)
|
12.31 in2
(7942 mm2)
|
122 lbs.
(55 kg)
|
|
100 tons
(890 kN)
|
Air or Electric
Double Acting
|
13-1/2"
(343 mm)
|
Gear Box: 8.5" x 12"
(216 x 305 mm)
Cylinder Dia.: 4.63"
(118 mm)
|
6"
(152 mm)
|
25"
(635 mm)
|
3-1/8"
(79 mm)
|
20.63 in2
(13310 mm2)
|
270 lbs.
(123 kg)
|
|
150 tons
(1334 kN)
|
Air or Electric
Double Acting |
12-1/4"
(311 mm)
|
5"
(127 mm)
|
24"
(610 mm)
|
2-1/2"
(64 mm)
|
30.1 in2
(19419 mm2)
|
243 lbs.
(110 kg)
|
|
200 tons
(1779 kN)
|
Air or Electric
Double Acting
|
16"
(406 mm)
|
Frame: 11" x 11"
(305 x 305 mm)
Nose: 7" Dia.
(178 mm)
|
8"
(203 mm)
|
37"
(940 mm)
|
4"
(102 mm)
|
40.45 in2
(26097 mm2)
|
455 lbs.
(203 kg)
|
|
|
|
|
|
|
|
|
| T8Z-18 Hydraulic Torque Wrench |
 |
| The hydraulic torque wrench is used for tensioning anchors in tight fitting locations where it would be difficult to use an hydraulic jack. The wrench is also recommended for use when setting the large diameter Spin-Lock anchors. The torque wrenches are light weight and can achieve a maximum of 8,000 ft-lbs. Torque Tensioning charts Williams products can be found here. |
Maximum
Torque |
Length |
Height |
Weight |
5,590 ft./lbs.
(773 kg/M) |
11.11"
(279 mm) |
4.49"
(114 kg) |
16.75 lbs.
(7.6 kg) |
8,000 ft.lbs.
(1,006 kg/M) |
12.57"
(319 kg) |
5.09"
(129 kg) |
24.95 lbs.
(11.3 kg) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| T8Z-04 Torque Multiplier (4:1)
For use with T8Z Torque Wrench. Other sizes available.
|
 |
| Size |
Square Drive
Input |
Square Drive
Output |
Maximum
Torque |
| GA 186 |
1" |
1-1/2" |
4,000 (ft. lbs.) |
|
|
|
|
|
|
|
|
|
| T9F Impact Tool
Lightweight air impact guns for applying torque to anchor bolts when setting or tensioning the anchor assembly.
|
 |
| Size |
Bolt Diameter |
Square Drive |
TorqueCapacity |
| T9F-06 |
3/4" to 1" |
3/4" |
600-1,100 (ft. lbs.) |
| T9F-08 |
1" to 1-3/8" |
1" |
1,700-2,000 (ft. lbs.) |
| T9F-12 |
1-3/8" to 2" |
1-1/2" |
3,000-4,000 (ft. lbs.) |
|
|
|
|
|
|
|
|
|
| T1Z & T2Z Long Fitting Tool Adapters
For driving hex nuts and setting tools, typically with our Spin-Lock anchor systems. Works with torque wrench or impact gun.
Available with 1" or 1-1/2" square drive. Please specify square drive for compatibility with your equipment.
|
T2Z Regular Socket |
T1Z Deep Socket |
|
|
|
|
|
|
|
|
| K3F-26 Long Fitting Wrench Adapter
For applying torque to recessed anchor nuts that are under tension when using hydraulic jacks. Available in all anchor sizes.
|
 |
|
|
|
|
|
|
|
|
| T3Z Hex Knocker Wrench
Used for safe hex nut adjustment inside of open frame jacks.
|
 |
|
|
|
|
|
|
|
|
| Spin Adapter
This tool provides a transition between the drill steel and the setting tool when the drilling equipment is used to spin the anchor bar through the resin cartridges. Adaptations to various drill steel types are available and must be specified when placing an order.
|
 |
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
 Williams Form Engineering Corp. All rights reserved. |
|
