|
|
|
S7 Reuseable Concrete Anchor Accessories
|
|
|
|
|
|
 |
|
|
|
|
|
 |
|
|
H1F Heavy Duty Hex Nuts - ASTM 194 Grade 2H
|
|
|
 |
Bar
Diameter |
Across
Flats |
Across
Corners |
Thickness
|
Part
Number
|
1/2" - 13 UNC
(12 mm) |
7/8"
(22.2 mm) |
1.01"
(25.7 mm) |
31/64"
(12.3 mm) |
H1F-04 |
3/4"- 10 UNC
(20 mm) |
1-1/4"
(31.8 mm)
|
1.44"
(36.7 mm)
|
47/64"
18.7 mm)
|
H1F-06
|
1"- 8 UNC
(25 mm) |
1-5/8"
(41.3 mm)
|
1.88"
(47.7 mm)
|
63/64"
(25.0 mm)
|
H1F-08
|
1-1/4"- 7 UNC
(32 mm) |
2"
(50.8 mm)
|
2.31"
(58.6 mm)
|
1-7/32"
(31.0 mm)
|
H1F-10
|
1-3/4"- 5 UNC
(45 mm) |
2-3/4"
(69.9 mm)
|
3.18"
(80.6 mm)
|
1-23/32"
(43.7 mm)
|
H1F-14
|
2" - 6 UN
(51 mm) |
3-1/8"
(79.4 mm)
|
3.61"
(91.7 mm)
|
1-31/32"
(50.0 mm)
|
H1F-16
|
|
|
|
|
|
|
|
|
|
C2T Stop-Type Couplings - ASTM A108 |
|
|
|
 |
Bar
Diameter |
Outside
Diameter |
Overall
Length |
Part
Number
|
1/2" - 13 UNC
(12 mm) |
3/4"
(19 mm) |
1-1/2"
(38 mm) |
C2T-04 |
3/4"- 10 UNC
(20 mm) |
1-1/8"
(29 mm)
|
2"
(51 mm)
|
C2T-06
|
1"- 8 UNC
(25 mm) |
1-1/2"
(38 mm)
|
3"
(76 mm)
|
C2T-08
|
1-1/4"- 7 UNC
(32 mm) |
1-7/8"
(47 mm)
|
3-3/4"
(95 mm)
|
C2T-10
|
1-3/4"- 5 UNC
(45 mm) |
2-1/2"
(65 mm)
|
5-1/2"
(140 mm)
|
C2T-14
|
2" - 6 UN
(51 mm) |
3"
(76 mm)
|
6"
(152 mm)
|
C2T-16
|
|
|
|
|
|
|
|
|
|
R9F Hardened Washers - ASTM F436 |
|
|
|
 |
Bar
Diameter |
Outside
Diameter |
Inside
Diamter |
Thickness |
Part
Number
|
1/2" - 13 UNC
(12 mm) |
1-3/8"
(35 mm) |
9/16"
(14 mm) |
9/64"
(3.6 mm) |
R9F-04-436 |
3/4"- 10 UNC
(20 mm) |
1-15/32"
(37 mm)
|
13/16"
(21 mm)
|
9/64"
(3.4 mm)
|
R9F-06-436
|
1"- 8 UNC
(25 mm) |
2"
(51 mm)
|
1-1/8"
(28 mm)
|
5/32"
(4.0 mm)
|
R9F-08-436
|
1-1/4"- 7 UNC
(32 mm) |
2-1/4"
(57 mm)
|
1-3/8"
(35 mm)
|
5/32"
(4.0 mm)
|
R9F-10-436
|
1-3/4"- 5 UNC
(45 mm) |
3-3/8"
(86 mm)
|
1-7/8"
(48 mm)
|
7/32"
(5.6 mm)
|
R9F-14-436
|
2" - 6 UN
(51 mm) |
3-3/4"
(95 mm)
|
2-1/8"
(54 mm)
|
7/32"
(5.6 mm)
|
R9F-16-436
|
|
|
|
|
|
|
|
|
|
Steel Plates |
|
|
|
|
|
|
|
|
|
|
|
End Caps |
|
|
|
Williams offers end caps produced from fiber reinforced nylon, steel or PVC to provide corrosion protection at otherwise exposed anchor ends. Most often the caps are packed with corrosion inhibiting wax or grease. Caps made from reinforced nylon and steel are used in exposed impact areas. The fiber reinforced nylon end cap meets the Florida DOT standards.
|
|
|
|
 |
 |
 |
 |
 |
| Fiber Reinforced Nylon Cap |
Slip-On PVC Cap
with Plastic Nut |
Screw-On
PVC Cap |
Steel Tube
with Jam Nut |
Steel Tube Welded on Flange with Threaded Screw Connections |
|
|
|
|
|
|
|
|
Eye Nuts |
|
|
|
Williams Eye Nuts may be used as lifting eyes for forms, concrete blocks, concrete cylinders, machinery or equipment. The large base on three of the models makes them excellent for anchoring guy wires. Safety factors and working loads based on the ultimate strength of the Eye Nuts should be determined for the specific application by the project design engineer. |
|
|
|
 |
 |
 |
 |
 |
 |
 |
| NEB 1 |
NEB 50 |
NEB 75R |
NEB 100 |
NEB 200 |
E1N |
CCF 1-4 |
|
|
|
|
Eye Nut
Designation |
Inside
Width |
Inside
Height |
Ring
Diameter |
Overall
Height |
Taps
Available |
Straight Tension
Ultimate
Strength |
Blank Part
Number |
NEB 1
Ductile Iron |
2"
(51 mm) |
2"
(51 mm) |
1-1/8"
(29 mm) |
5-1/8"
(130 mm) |
3/4"; 7/8"; 1"*
(20; 22; 25 mm) |
35 kips
(156 kN) |
E1M-00-001 |
NEB 50
Ductile Iron |
3"
(76 mm) |
3'
(76 mm) |
1"
(25 mm)
|
5-3/4"
(146 mm)
|
1/2"; 3/4"
(13; 20 mm)
|
26 kips
(116 kN)
|
E1M-00-050
|
NEB 75R
Ductile Iron |
4"
(102 mm)
|
5"
(127 mm)
|
1"
(25 mm)
|
7-3/4"
(197 mm)
|
1/2"; 3/4"
(13; 20 mm)
|
23 kips
(102 kN)
|
E1M-00-75R
|
NEB 100
Ductile Iron |
4"
(102 mm)
|
4-1/2"
(114 mm)
|
1-1/4'
(32 mm)
|
8"
(203 mm)
|
1"; 1-1/4"; 1-3/8"*
(25; 32; 35 mm)
|
65 kips
(289 kN)
|
E1M-00-100
|
NEB 200
Ductile Iron |
5"
(127 mm)
|
6"
(152 mm)
|
2"
(51 mm) |
11"
(274 mm)
|
1-3/8"; 2"
(35; 51 mm)
|
150 kips
(667 kN)
|
E1M-00-200
|
E1N
Malleable |
2"
(51 mm)
|
2-1/2"
(64 mm)
|
7/8"
(22 mm)
|
5-1/8"
(130 mm)
|
Grade 75
#6, #7, #8
|
35 kips
(156 kN)
|
E1M-00-E1N
|
CCF 1
CCF 2
CCF 3
CCF 4
Steel |
up to
4"
(102 mm)
|
up to
6-1/4"
(159 mm)
|
up to
1-1/2"
(38 mm)
|
up to
8-1/2"
(216 mm)
|
Grade 75
#6 through
#18
|
up to
260 kips
(1157 kN)
|
E1M-00-CCF1
E1M-00-CCF2
E1M-00-CCF3
E1M-00-CCF4
|
* 150 KSI All-Thread-Bar may not be used in 1" diameter for the NEB 1 or in 1-3/8" diameter for the NEB 100. |
|
|
|
|
|
|
|
S97 Setting Tool
|
|
|
|
| This tool is required for torque setting the Spin-Lock anchors or for spinning rebars into resin cartridges without jamming or scoring the bolt threads. Special two piece design allows lower hex to be held in place while upper hex is loosened for easy removal.
Hardened steel allows for several reuses. Two piece design assures easy removal. Other thread forms are available for all Williams anchors.
|
Bar
Diameter |
Part
Number
|
1/2" - 13 UNC
(12 mm) |
S9Z-004 |
3/4"- 10 UNC
(20 mm) |
S9Z-006 |
1"- 8 UNC
(25 mm) |
S9Z-008 |
1-1/4"- 7 UNC
(32 mm) |
S6Z-0H-010 |
1-3/4"- 5 UNC
(45 mm) |
S6Z-0H-012 |
2" - 6 UN
(51 mm) |
S6Z-0H-016
|
|
 |
 |
|
Setting tools are included with each full box of anchors up to 1" diameter. For above 1" diameter anchors use Williams S6Z Rock Bolt Setting Tool
|
S97 Setting Tool |
S6Z Setting Tool |
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
 Williams Form Engineering Corp. All rights reserved. |
|
