Williams Form Engineering Corp. Williams Form Engineering Corp.
Williams Form Engineering Corp.
DownloadsDownloadsWhat's NewContact UsAbout UsWilliams Form Engineering Corp.
Ground Anchor Systems
Concrete Anchor Systems
Post Tensioning Systems
Threaded Bars with Fasteners
Tie Rods & Tie Backs
Micro Piles
Concrete Forming Hardware Systems
Williams products are made in the USA

Epoxy Anchor Installation Equipment

Epoxy Anchor
Information
Epoxy Anchor
Design
Epoxy Anchor Applications Parts &
Accessories
Epoxy Anchor
Installation
Epoxy Anchor
Equipment
Case
Histories
Corrosion
Protection
Manual Epoxy Dispenser Mixing Nozzel
Hydraulic Jacks Post-Tensioning Jacks
Hydraulic Torque Wrench Manual Torque Wrench
Torque Wrench Multiplier Long Fitting Tool Adapters
Long Fitting Wrench Adapters Hex Knocker Wrench
Manual Epoxy Dispenser

A pneumatic epoxy dispenser is available for the 53 oz. cartridge.

Mixing Nozzel
T7Z Hydraulic Jacks Hydraulic Jack

Used for testing and pre-stressing anchor bolts. Available with up to 5-1/8" center hole. Unit comes with ram, pump, gauge, hoses, jack stand, high strength coupling, high strength test rod, plate, hex nut and knocker wrench. Calibrations are available upon request.

Note: Jack pull rods should have a higher capacity than the anchor rod.

Jack
Capacity
Pump
Method
Ram
Height
Base
Size
Ram
Travel
Minimum
Total
Height
of Ram
& Frame
Maximum
Test Rod
Diameter
Ram
Area
Approx.
Total
Weight
of Ram
& Frame
10 tons
(89 kN)
Hand
Single Acting
5-5/16"
(135 mm)
3" Dia.
(76 mm)
2-1/2"
(64 mm)
8-3/8"
(213 mm)
3/4"
(19 mm)
2.12 in2
(14 cm2)
12 lbs.
(5.4 kg)

30 tons
(267 kN)

Hand
Single Acting

6-1/16"
(154 mm)

8" x 8"
(203 x 203 mm)

3"
(76 mm)

19"
(483 mm)

1-1/4"
(32 mm)

5.89 in2
(38 cm2)

80 lbs.
(36 kg)

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

9-1/2"
(241 mm)

8" x 8"
(203 x 203 mm)

5"
(127 mm)

29"
(737 mm)

2"
(51 mm)

12.31 in2
(79 cm2)

153 lbs.
(69 kg)

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

12-3/4"
(324 mm)

9" x 9"
(228 x 228 mm)

6-1/2"
(165 mm)

29"
(737 mm)

2"
(51 mm)

12.73 in2
(82 cm2)

225 lbs.
(102 kg)

100 tons
(890 kN)

Air or Electric
Double Acting

13-1/2"
(343 mm)

9" x 9"
(228 x 228 mm)

6"
(152 mm)

35"
(889 mm)

3-1/8"
(79 mm)

20.63 in2
(133 cm2)

270 lbs.
(123 kg)

100 tons
(890 kN)
Air or Electric
Double Acting

12-3/8"
(314 mm)

9" x 9"
(228 x 228 mm)

6"
(152 mm)

28"
(711 mm)

2"
(51 mm)

20.03 in2
(129 cm2)

192 lbs.
(87 kg)

150 tons
(1334 kN)

Air or Electric
Double Acting

12-1/4"
(311 mm)

12" x 12"
(305 x 305 mm)

5"
(127 mm)

32-1/4"
(819 mm)

2-1/2"
(64 mm)

30.1 in2
(194 cm2)

350 lbs.
(159 kg)

200 tons
(1779 kN)

Air or Electric
Double Acting

12-1/4"
(311 mm)

12" x 12"
(305 x 305 mm)

8"
(203 mm)

34"
(864 mm)

4-1/16"
(103 mm)

40.45 in2
(261 cm2)

518 lbs.
(235 kg)

200 tons
(1779 kN)

Air or Electric
Double Acting

27-1/2"
(699
mm)

12" x 12"
(305 x 305 mm)

15"
(381 mm)

49-1/4"
(1250 mm)

4"
(102 mm)

40.45 in2
(261 cm2)

604 lbs.
(274 kg)

300 tons
(3558 kN)

Electric
Double Acting

27-1/2"
(699 mm)

15" Dia.
(381 mm)

15"
(381 mm)

50-1/2"
(1283 mm)

5-3/8"
(137 mm)

78.5 in2
(590 cm2)

1400 lbs.
(635 kg)

400 tons
(3558 kN)

Electric
Double Acting

18-3/4"
(476 mm)

15" Dia.
(381 mm)

6"
(152 mm)

45-3/4"
(1162 mm)

4-1/4"
(108 mm)

91.5 in2
(590 cm2)

1300 lbs.
(590 kg)

Certification of gauge accuracy available on request prior to shipment only.
Hydraulic Jack Detail

T80 Post-Tensioning Jacks

Post-Tensioning Jack

With the T80 series the enclosed bearing housing contains a geared socket drive to tighten the bolt hex nut during tensioning. Test jack housing will accommodate up to a 9” deep pocket.

Jack
Capacity
Pump
Method
Ram
Height
Base
Size
Ram
Travel
Minimum
Total
Height
of Ram
& Frame
Maximum
Test Rod
Diameter
Max.
150 KSI
Bar Size
Ram
Area
Approx.
Total
Weight
of Ram
& Frame

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

9-1/2"
(241 mm)

Gear Box: 8.5" x 20.5"
(215 x 520 mm)
Cylinder Dia.: 3.63"
(92 mm)

5"
(127 mm)

33"
(838 mm)

2"
(51 mm)

1"
(25 mm)

12.31 in2
(79 cm2)

122 lbs.
(55 kg)

60 tons
(534 kN)

Hand, Air or Electric
Double Acting

12-3/4"
(324 mm)

6-1/2"
(165 mm)

36"
(914 mm)

2"
(51 mm)

1-1/4"
(25 mm)

12.73 in2
(82 cm2)

225 lbs.
(102 kg)

100 tons
(890 kN)

Air or Electric
Double Acting

13-1/2"
(343 mm)

Gear Box: 8.5" x 20.5"
(215 x 520 mm)
Cylinder Dia.: 4.63"
(118 mm)

6"
(152 mm)

39"
(991 mm)

3-1/8"
(79 mm)

1-3/8"
(35 mm)

20.63 in2
(133 cm2)

270 lbs.
(123 kg)

150 tons
(1334 kN)

Air or Electric
Double Acting

12-1/4"
(311 mm)

5"
(127 mm)

28"
(711 mm)

2-1/2"
(64 mm)

1-3/8"
(35 mm)

30.1 in2
(194 cm2)

243 lbs.
(110 kg)

200 tons
(1779 kN)

Air or Electric
Double Acting

16"
(406 mm)

Frame: 11" x 11"
(305 x 305 mm)
Nose: 7" Dia.
(178 mm)

8"
(203 mm)

37"
(940 mm)

4"
(102 mm)

1-3/4"
(45 mm)

40.45 in2
(261 cm2)

455 lbs.
(203 kg)

T8Z-18 Hydraulic Torque Wrench Hydraulic Torque Wrench
The hydraulic torque wrench is used for tensioning anchors in tight fitting locations where it would be difficult to use an hydraulic jack. The wrench is also recommended for use when setting the large diameter Spin-Lock anchors. The torque wrenches are light weight and can achieve a maximum of 8,000 ft-lbs. Torque Tensioning charts Williams products can be found here.
Maximum
Torque
Length Height Weight
5,590 ft./lbs.
(773 kg/M)
11.11"
(279 mm)
4.49"
(114 kg)
16.75 lbs.
(7.6 kg)
8,000 ft.lbs.
(1,006 kg/M)
12.57"
(319 kg)
5.09"
(129 kg)
24.95 lbs.
(11.3 kg)
T8Z Torque Wrench

For applying torque to the anchor bolt when setting the anchor. Torque Tensioning charts Williams products can be found here.

Bolt
Diameter
Square
Drive Size
Capacity
(ft. lbs.)
*1/2"-1" 3/4" 0-500
1/2"-1" 3/4" 0-600
*1-1/8"-2" 1" 0-1,000
*Available with Ratchet Adapter
Torque Wrench
T8Z-04 Torque Multiplier (4:1)

For use with T8Z Torque Wrench. Other sizes available.

Torque Multiplier
Size Square Drive
Input
Square Drive
Output
Maximum
Torque
GA 186 1" 1-1/2" 4,000 (ft. lbs.)
T1Z & T2Z Long Fitting Tool Adapters

For driving hex nuts and setting tools, typically with our Spin-Lock anchor systems. Works with torque wrench or impact gun.
Available with 1" or 1-1/2" square drive. Please specify square drive for compatibility with your equipment.

Long Fitting Tool Adapter - Regular Socket
T2Z Regular Socket
Long Fitting Tool Adapter - Deep Socket
T1Z Deep Socket
K3F-26 Long Fitting Wrench Adapter

For applying torque to recessed anchor nuts that are under tension when using hydraulic jacks. Available in all anchor sizes.

Long Fitting Wrench Adapter
T3Z Hex Knocker Wrench

Used for safe hex nut adjustment inside of open frame jacks.

Knocker Wrench
Williams Form Engineering Corp.
Epoxy Anchor
Information
Epoxy Anchor
Design
Epoxy Anchor Applications Parts &
Accessories
Epoxy Anchor
Installation
Installation
Equipment
Case
Histories
Corrosion
Protection
Contact Us Home
Williams Form Engineering Corp. All rights reserved.